The content down below involving How to Install a Bathtub: Install an Acrylic Tub and Tub Surround is really stimulating. Check it out yourself and figure out what you think about it.
Setting up a bathtub isn't precisely brain surgery, however it does call for strong plumbing, woodworking, and also in some cases, tiling abilities. Changing an old tub with a new one is additionally a moderately challenging project. If the old tub is conveniently easily accessible, the job can move rapidly; if you have to open up a wall to get rid of the old tub and also position the brand-new bathtub, the job is a lot harder. In either situation, the task is within a home handyman's abilities, although you will certainly need a helper to move out the old tub and also embeded in the brand-new one. See to it you have actually qualified yourself for the job and are comfortable trying it. Rather than employing a contractor to take over a halfway-completed task, it is far better to think about using one prior to you start. Possibilities are you may require a professional plumber to make tube connections.
This post will aid you mount a brand-new bathtub in your washroom if you have already acquired a new bathtub and don't need to transform the setup of your previous water system pipes.
Your devices and also material checklist ought to consist of the following:
- New Bathtub
- Hammer
- Pipeline Wrenches
- Prybar
- Safety Glasses
- Degree
- Pliers
- Adjustable Wrench
- Putty Blade
- Screwdriver
- Cold Blade
- Measuring tape
- Pipeline Caps
Planning for the Installation
First of all, the sustaining framework provided with the bathroom ought to be fitted (if needed) according to the maker's guidelines. Next off, fit the taps or mixer to the bathtub. When fitting the tap block, it is important to make certain that if the faucet includes a plastic washing machine, it is fitted between the bath and the faucets. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the taps unit to prevent strain on the bath tub.
Fit the flexible faucet connectors to the bottom of both faucets making use of 2 nuts and olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet through the hole in the bathroom. Utilize the nut supplied by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. See to it you make use of every one of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bath must currently be ready to be suited its last position.
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installation, then the first thing you should do is detach the supply of water. After doing so, activate the taps to drain pipes any kind of water staying in the system. The process of getting rid of the existing taps can be quite troublesome due to the restricted access that is usually the case.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipelines to the taps. Have a towel all set for the continuing to be water that will certainly come from the pipelines. When the supply pipelines have been eliminated, make use of the same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single taps from turning during this process. When the taps have actually been removed, the holes in the bath/basin will certainly need to be cleaned up of any kind of old sealing substance.
Before going on to fit the brand-new taps, contrast the pipeline links on the old faucets to the new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is required for the new taps to fit.
Setting up the Tub
Utilizing both wood boards under its feet, position the bathtub in the called for position. The wood boards are valuable in equally spreading out the weight of the tub over the area of the boards instead of focusing all the weight onto four small factors.
The following objective is to make sure that the bath tub is leveled all round. This can be achieved by inspecting the level and readjusting the feet on the tub until the level reviews level.
To install faucets, fit all-time low of the outermost versatile tap port to the suitable supply pipeline by making a compression join; after that do the exact same for the various other faucet.
Switch on the supply of water and inspect all joints as well as brand-new pipework for leaks and tighten them if needed. Fill the tub as well as additionally inspect the overflow electrical outlet and also the regular electrical outlet for leakages.
Finally, deal with the bath paneling as defined in the producer's user's manual. Tiling as well as sealing around the bathtub needs to wait up until the bathtub has been used at the very least when as this will settle it right into its last position.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will certainly need a plastic adapter to stop damage to the string. One end of the connector fits on the plastic tail of the faucet and also the various other end provides a connection to the current supply pipelines.
If you require to fit a monobloc, then you will need reducing couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next off, position the tap in the installing opening in the bath/basin guaranteeing that the washing machines remain in location in between the tap as well as the sink. Secure the faucet in position with the maker provided backnut. When the faucet is securely in place, the supply pipelines can be linked to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with normal tap ports. The previous type should be linked to the faucet ends initially, tightening only by hand. The supply pipelines can later on be connected to the other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Bath tub
In the area where the bath satisfies the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is important as the installation can relocate sufficient to split an inflexible seal, causing the water to pass through the wall surface between the bathroom and the tiling, bring about issues with moisture and also possible leaks to the ceiling listed below.
You can select from a variety of coloured sealants to blend in your fixtures and installations. They are sold in tubes and cartridges, as well as can securing voids up to a size of 3mm (1/8 inch). If you have a larger void to load, you can load it with spins of soaked paper or soft rope. Keep in mind to constantly fill the bath tub with water before securing, to allow for the motion experienced when the bathtub is in use. The sealer can break rather very early if you do not take into consideration this movement prior to sealing.
Alternatively, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally quickly readily available on the marketplace. It is advisable to fit the floor tiles making use of waterproof or waterproof glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

Hopefully you enjoyed our piece about How to Install a Bathtub Yourself. Thank you for taking the time to browse our piece. Do you know someone else who is interested by the subject? Please feel free to promote it. Thanks a lot for your time. Don't forget to visit our website back soon.
Request Service
Comments on “Important Plumbing Insights for Bathtub Installation”